4SO8 Set of 4 pcs. hex stand-offs M4x8mm incl. screws, washers and a hex key
4SO10 Set of 4 pcs. hex stand-offs M4x10mm incl. screws, washers and a hex key
In case you are missing your bracket these are sold as kits separately. All CIOKS power supplies are now sold with all the needed hardware to mount them underneath a Pedaltrain board.
This Flex cable allows you to power two pedals of one outlet. Both pedals must be with 5,5/2,1mm centre negative input power socket which is also called the BOSS standard. Two cables go from the plug at the power supply end to the two pedals, one is 30cm long and the other 50cm.
Also calleded the BOSS standard. This Flex type should be used to power the vast majority of the pedals on the market like BOSS, TC Electronic, Strymon, Dunlop, MXR, Catalinbread, ZVex and many many more.
With this Flex cable you can power three pedals of one outlet. All three pedals will get the same voltage as stated on the outlet and have a 5,5/2,1mm centre negative power jack also called the BOSS standard. Cable length is 50 then 30 and again 30cm to the last DC plug.
This standard is less popular but also widely used in all Moogerfooger or Radial Tonebone pedals, a few Empress, Diamond and Kingsley pedals, the ’69 Pedal, Soulbender or Octafuzz from Fulltone or older positive ground pedals.
This Split adapter Flex allows you to power two pedals with the same voltage of a single outlet where you can choose the cable length and the plug type individually for each of the two pedals.
This standard is very rarely seen in pedals where we only know three applications. But you can use it for your AC pedal to distingush the Flex cable used for AC from all the others on your board.
This very simple Flex cable is just an extension providing an extra 50cm length to any other Flex cable.
This Flex cable type should be used to power all Eventide Factor and H9 pedals, older 4-button modelers from Line 6 like the DL4,, some older 18, 24 or 40V Electro-Harmonix pedals and most of the AC powered pedals.
This black type 5 Flex cable with a 3,5mm mini jack plug should be used to power some older Electro-Harmonix, DOD, some Wah or RAT pedals, the KLON Centaur and many others.
This Series adapter Flex adds voltages of two isolated outlets used. If you need say 18 or 24V and want to choose the plug type and cable length to the pedal this is the way to go. Preferably use two outlets with same current rating.
Need more mA than a single outlet can provide. Use this Parallel adapter Flex to add currents from two same isolated outlets. Voltage and current rating of the outlets used must be exactly the same.
The 9V battery snap on type 6 Flex cable should be used with 9V battery powered pedals which don’t have an adapter input socket e.g. vintage Wah pedals or some MXR or Roger Meyer fuzz pedals.
Adds voltages of two outlets used. This special Flex combines a series connection with a standard Flex in one cable. Available with type 1 black BOSS standard plug or the green type 4 mainly for older 24V EHX pedals. Preferably use with two outlets with same current rating.
This blue Flex cable can only be used to power one of the eight vacuum tube pedals from Electro-Harmonix which should be powered with 12V AC.
Rubber feet to raise your pedalboard, sold in sets of 4 pcs. incl. rivets.
Spare rubber feet for CIOKS power supplies.
Use a single 9V or 12V outlet to power a low current 18V or 24V pedal. The pedal should not draw more than 50mA.
Two cables which allow you to make custom length Flex cables. One with our standard RCA plug and the same cable type used on all the other Flex cables. The other is with round cable and a space saving angled RCA plug.
OVERKILL: an excess of something beyond what is required or suitable for a particular purpose – 25 isolated outlets and massive amounts of POWER!!! Second to none!
Nice power supply for medium pedal boards with 6 isolated outlets and a total of 1.000mA DC. Two outlets are configurable to 18V.
Nice power supply with 6 outlets of which two are powerful with 400mA each. Good choice for smaller rigs with two high current pedals like Eventides or big Strymons.
Powerful AC section with 9 or 12V AC, nice add-on with AC to another link power supply or a stand-alone for a small rig with one AC pedal e.g. Whammy.
Adam link is very flat and fits below Pedaltrain nano+ and all metro pedalboards, has 4 isolated outlets and can power any two Strymon pedals of its two 250mA outelets – small and afordable.
The most versatile and powerful unit with 16 outlets in 12 isolated sections. Adjustable 4-15V outlet, two outlets configurable to 15V, two 800mA AC sections with 9 or 12V AC, one also with 16V AC and plenty of power with DC.
Adjustable 9-24V high current outlet with mA-meter, 10 isolated outlets with loads of DC power, state of the art power supply for big rigs.
Very popular all-rounder with versatility and plenty of power. Premium choice with 10 outlets in 8 isolated sections for a bigger pedal board.
Super nice power supply for bigger boards with 8 isolated outlets, four outlets with 300mA and one with voltages 9, 12, 15 or 18V and current up to 600mA.
Nice stand-alone power supply for small to medium rigs with 8 outlets in 6 isolated sections. Each of the two 300mA sections will power any Strymon or Eventide pedal.
Good solution if you have one or two AC pedals plus some DC pedals. Has two 800mA AC sections with 9 or 12V AC, one also with 16V AC. With only one AC pedal you get 1.000mA of DC with 9, 12 or 15V available.
Fits below Pedaltrain nano+ and all metro pedalboards, has 5 isolated outlets, two 300mA outlets will power any two high current pedals like Strymons or Eventides, one outlet can be set to 18V – flat, small yet powerful.
A pink version of the top selling DC10 with 10 outlets in 8 isolated sections without the Merge feature but with a non-matched appereance if you dare.
Will power four Eventide pedals, five with additional Parallel adapter Flex, with 3+ Eventide pedals on board plus other DC pedals this is the way to go.